Search results

Hi I have 98 GC 4.0L, since i'm on vacation from work I did not use the jeep at all last couple of days and today i went to turn it on, the battery was dead. so I had a friend help jump started but, when it turn on I would not stay runnig. i had to keep pressing the GAS in oprder for it no to...

Hi recently i changed my disk brake rotor, and pads. and to my suprise one of the bolts that holds the caliper to the steering knuckle was missing!!. also when i tried to put the other one in it never tightens, so I have an issue the threads. So has any one tried to repair the threads on a...

hi to all, (JZ 1998 4.0 L6) I recently was able to fix astalling problem, but to find it i did a lot of stuff that did not help. One was I took out the CAT converter, and the O2 sensor that was attached to it now i'm wondering if this is causing this problem ideas? all though my back fireing...

HI to all.. for a long while now I've had a stalling problem I went allover different forums trying to find a solution. Tried many fixes like cutting the cover screws on the ECM in half or tying the cable harness. And did not work. So after a LOT of trouble shooting fond that the screws the...

Hi to all. long time since my las visit.. My ZJ is a 1998 L6 4.0 grand Cherokee, lately i been having problems were my car stops accelerating or loosing power. some times it so bad that the car will stall i have to pull over. and when it doesn't stall it backfires. looking in some trouble...

OK a couple of weeks ago I did a post about my jeep stalling while driving and how i was sometimes able to save it from stalling if I down shifted. So the advise was to take a look at the trany solenoids or torque converter, so i took it to a shop and they could not find anything to explain...

hi to all my 98 GCL, stalls when iddling. when I go to turn it on in the morning and let it idle the car will turn off by it self after about 5 to 10 min every time on the first try after that its hard to start again. even after it starts it will shut off again. I go through this ritual...

Hi my jeep is a ZJ 1998 grand cherokee laredo 4x4 I6 4.0L engine I have had this problem for long time now, found treads here and in other forums about similar problems and there fixes but they have not worked on mine the last one i did is I took it to a shop the said it was the PCM but it...

Hi to all I have noticed i very hard kick when dwon shifting from 2nd-->1st whe at low speed like when in heavy traffic, to confirm it I drove around at very slow speed les than 15mph in drive and in 2nd . i need some opnions before tacking to the shop, a friend told me I shoul add some trany...

Hi to all My jeep is 98 GC Laredo 4x4 L6 4.0 motor. recently it has been turning off when ever it wants to and I get the P0351 error code (Low curent in Coil primary circuit ) I checked the wiring for coil to ASD relay and to the PCM and both are OK, yesterday i checked the primary...

Hi to all I have a 98 grand Cherokee 4x4 4.0L 6cyl. My battery is being drained tothe point were it will not stay charged even if a disconect de terminals. this is what i´ve done I disconected the PCM, took out all the fuse that are in passenger side, disconected the module that is under the...

Hi to all my Jeep is a 1998 Grand Cherokee Laredo L6 4.0 while cleaning my air filter, I found a hos that goes to the top of the front differential but the other end was setting under the air filter tray and is not connected to anything. need help knowing what to do in the HAYES manual can't...

Hi My jeep GC Laredo 1998 4.0 6L. turns off while idling and also while runnig and is hard to start. changed the Crack Position sensor, got new a sparck plugs and wireset, problem continues. I had the check engine light on the code was P0351 (Ignition Coil 1 control circuit), but my jeep only...

Hi to all My jeep takes 2-3 trys before it starts, and it runs like the timing is bad, acouple of weeks ago it started turnning off for no reason while idling, and couple of times while running. yesterday the transmission had a hard time shifting in to 3rd gear. and takes a long time to shift...