Search results

1069923 :oops: The gauge seems to work normally, sometimes erratically, although I am going to install a new sending unit just in case. Also I just purchased a new 3 core radiator off e-bay for $167 which may help a little (current origional radiator is a bit clogged). May as well change out...

1070146 :-D Tampa Florida until September then Sacramento, CA. Killer Jeep Mr. Tom. 8-) [addsig]

1070296 Since I don't have a hoist or a puller, is there anyway to support the engine from underneath? Thanks for the help by the way! 8-) [addsig]

1070333 Thanks Fish. That's usually about how I end up doing things - wedge, tug, swear, etc.. It's good to know that it CAN be done without an engine lift! :-P [addsig]

1070397 8-) :lol: Ahh the light at the end of the tunnel. I'm in purchase mode right now. Morgster, how much did you pay for those bombproof jobbers, would you recommend them over the Daystar poly ones? Thanks guys, this is why I keep coming back to this site!! You Rock! :evil: [addsig]

1070475 :-D Thanks again Morgster, I just ordered the bombproof mounts - zinc plated. Can't wait until they arrive. By the way - your site is excellent and that is one clean engine compartment. Where in CA do you live? I'll be moving to Sacramento in Sept. On a side note how difficult was your...

1046815 I just purchased my 89 and have begun the task of upgrading everything. During my tinkering, I have discovered the the pulse air system pipe leading to the cat has a rusted hole and a broken check valve. What sort of problems is this causing. Soon, I plan on performing the Nutter...

1047906 I'm pretty sure that this has been talked about before ----- However, I searched the previous 40+ pages and could not find any completely helpful answers. 1. Has anyone, who has completed the Nutter by-pass, been able to remove their pulse air system? Mine has rusted pipes and...

1048392 In trying to perform the bypass on my computer, I have come across numerous articles on the idle screws (curb idle, fast idle, etc.). Can someone explain and help me locate which is which. I am forever in the search of easy performance improvements and have come to realize that...

1052233 ARGH! does anyone have any tips for removing endlinks from a front sway bay on a 14 year old YJ. I have put WD-40 on the bolts for days, removed the nuts and frame supports. But I can't remove the links from the bar. I'm trying to put some poly replacement bushing on it. A...

1052789 :-( :-? My transfer case has a very slow leak. I believe that it is coming out the seal where it connects to the front of the rear drive shaft. Has anyone had any experience with re-sealing this area or any recommendations. I am hoping to avoid an expensive repair. 8-) [addsig]

1053831 8-) My T-case is leaking from the rear output oil seal onto the front U-joint of the rear drive shaft. I plan on replacing the rear oil seal and the rear mainshaft bushing inside of the rear extension housing. Has anyone completed theis repair? If you have, did you encounter any...

1053833 I'm looking at a set of 15x8 058's from quadratec for $79 per rim, does anyone know of a better deal on this style of rim? M/T Classic II run $95. Just want to make sure I'm not paying too much :-D :-D [addsig]

1054584 I am looking for an inexpensive and durable set of rocker guards. I've seen then from $200 and up. Does anyone know of how I can get a set a bit more reasonable? I'm just looking for some protection (plus cover up some treated rust spots). Help would be appreciated - Thanks! :-D :-D...

1063980 :-) Just curious if anyone has and how difficult it would be to mount a TJ rear bumper on a YJ. Seems like there are a good many available on ebay. 8-) [addsig]

1069839 :evil: Does anyone else have a 258 that puts off enough heat to thaw an iceberg? I have my carpet removed and after driving for 15 minutes the transmission hump gets extremely hot. In the winter that would be good. In FL in the summer - not good. I have put in a new water pump...

1070155 :roll: I know that this is probably an easy fix and I will most likly feel like an idiot when I read the answer, so here it goes. How do I and is it difficult to replace my motor mounts? You can stop smiling now and help a moron out. Thanks for your continued support! 8-) [addsig]