Search results

1068885 You can get rid of most of the vacuum line and solenoids if you still have them. You only need a couple. I try and find the link with a weber vacuum routing. Page title: Weber vacuum line [addsig]

1068888 I was having the same problem with my Weber. When I would floor it or get on a highway it would die down them kick in. I called weber you should have a 800 # for help if you need it . They told me to back out the idle speed screw, and adjust the idle mixture screw with a tachometer...

1069010 Hey chinard, just buy a seperate breather at Autozone or an autoparts store. It is a little filter that pops right into the rear grommet on the valve cover It will eliminate that hose. Were did you get the red vacuum hoses? edited by: jay89, May 27, 2003 - 04:54 AM[addsig]

1069216 Yeah snitty's right there are no nuts on the windsheild hinges. Just like mine the weld broke from the frame and the torx screw just kept spinning. I ended up having to drill them out and went to Home Depot to get toggle anchors with 1/4 in stainless bolts. Good luck. It is a pain in...

1069217 I took my heat exchanger off and never had a problem. Hot or cold and it was cold up here in Jersey this winter.[addsig]

1069219 Hey Chinard, How do you have your vac advance on the distributor running. It looks like you have it to manifold vacuum? And I noticed you have a juicbox. Doen't the juice box call for it to be hooked up to ported vacuum on the carb?[addsig]

1069304 HUH? :-? [addsig]

1069307 Run a separate switch. Run the yellow wire from the battery to the switch and the white from the switch to th lights. If you keep it like it is it will probably keep blowing the fuse because it is too much to have more lights on one fuse.[addsig]

1069308 Hey HI C I have Black hinges. Make me an offer? I'm in NJ. And you have too many pop ups on your website.[addsig]

1069535 Go with the K551 but if you have strict inspection laws it may not pass because it eliminates a lot of the vacuum and emission parts. My Weber works great. My only complaint is the nice chrome air filter cover is starting to rust already it has only been a couple of months.[addsig]

1069537 Does it really give you more power to switch to an electric fan? And do you have to re route the belts or do you just remove the fan and leave the pulley?[addsig]

1069734 I can't load pic. I copy and pasted the url in the signature box but it just shows the address not the pic? I got it working but why is the pic so big? I got it ! :-D edited by: jay89, Jun 03, 2003 - 01:25 PM[addsig]

1069737 I would alos check all you vac hoses for leaks?[addsig]

1069813 My brake booster goes to the manifold vacuum port just below the carb and above the egr![addsig]

1069814 How about some directions to the pine barrons? I would be taking the G.S. Parkway South?[addsig]

1069829 Manifold vacuum is constant where ported vacuum varies with speed. [addsig]

1069841 If you have your carpet out it lets the heat in. The padding and the carpet act as a heat shield. All vehicles get hot in that area. If you don't want carpet you may have to make a heat shield for underneath.[addsig]

1069842 I have a Weber and it runs great. When I first got it it would hesitate and back fire when I romped on it. You just have to find the perfect mixture. It takes a while but it works. I was told to back out the idle speed screw all the way and try and find the sweet spot with the air/fuel...

1064371 It shouldn't bounce more than 2 times. Down, up down up. Thats it.[addsig]

1064373 Just like bounty said. I would definitly remove the drive shaft.[addsig]