Search results

Tire Balancing 88Wrangles first off I have to appoligze to you. I should have taken the damn driveshaft off (while measuring) and payed a little more attention to the angle finder that I was using. (one size dos not fit all!! LOL) the correct measurments are now (drum roll?) tc output shaft...

RE: TJ water leak problem?????? that is jsut what I read on the angle finder thingy!! he he i assume it would be angled to 90* (seings how the patrs are so close to a horizontal line.) I believe in your description you were thinking of a vertical line. so back to math class here!! subtraction...

ok Igot 74* on the output on the axle and 84* on the TC output shaft. jsut out of courisoty what are the stock specs? now with those measurements what degree shims will I need?

so is the red what you are talking about or the blue? LOL

Re: RE: Re: RE: Re: RE: drive shaft angles? what should they ok a very simple drawing of what and where i measured.

Re: RE: Re: RE: 2006 FJ - It i measured on the top of the driveshaft and on the bottom of the driveshaft in the smae places up closer to the TC output shaft, drive shaft only not on the yokes or ujoints. or the output shafts them selves. i also measured the output shaft on the rear axle and...

RE: Re: RE: Re: RE: drive shaft angles? what should they be? so do you think by the measurements that a 4* shim would get them lined back up?

I do appreciate the help you guyz are giving. its jsut that I dont have the money to get a sye kit right now, and need a kind of fix to hold things over for a while till that really is a possiblity. as for play are you talking about an up and down play or in a twisting motion? left - right? I...

RE: Re: RE: drive shaft angles? what should they be? help!! to think it all started with the rear leafs saggin. :? :twisted:

RE: Finally a part of Jersey... I took the drive line off and checked the teeth on the output shaft on the Tc and it didnt have any major knicks, scoring, or signs or abnormal wearing. the origional U-joints!! (LOL) are stillin great condition considering, and yes they will be replaced. and no...

cool, can't wait it has only been doing this for maybe a week. I have checked the splines and they are no worse than any others with higher milage on them. decent engouh shpae to be used again i assure you.

I put in a 1" transfer case drop that came with the kit. and thx guyz!! i appreciate the help here!! I need to get this problem fixed right away as she is my daily driver!! I know stupid to lift a daily! !LOL

the drive shaft is BARLEY hanging on the end of the spline from the transfer case and it has enough up and down play to create vibrations in the drive shaft. when i acclerate and let off the pedal it has a disengaging type sound to it, and sometimes when moving with no power torque it vibrates a...

RE: Re: RE: 2006 FJ - It btw I dont have any problems with binding. not even all that close. maybe if it drooped quite a bit or something it would bind but wher eit is right now the drive shaft would fall off before that would happen!! LOL

i started with an rough country 4.5" lift full leaf packs and front coils, with some drop brackets and things. and recently added 1.5" shackels in the rear to even out the lift as I had 5.5' in front and 4.5" in the rear. no wit is at 5.5 in front and 5.5-6 in the rear. i didnt have any problems...

RE: homeschooling I just went out today and took some measurements, and am ready to buy some shims and a extension of the yoke to get rid of MY vibes. found out they are being cause by the stock yoke being too short and the driveshaft about to fall off the splines!! (yes she is down for the...

I swear on all jeepz!! that I had a tru 4.5" of lift in the rear. even if it didnt look like it to some, by the ways of measureing I know of (center of rim to bottom of fender) she measured 4.5" in the rear and 5.5" in the front. and with no audible or feelings of drive line vibes at all. she is...

RE: Wiring: york oba, cigarette lighter socket, radio again something im missing with the ujoints? (sorry to bring a post out of the dead like this but I would like to find out about this kind of stuff before hand so i can get all the parts needed before i dive in!! also one more thing...

2000jeeptj upper sliding windows jsut the rear got lifted. made everything come to life!! LOL I measured the front is at 5.5" and the rear is at 6" tire size well thinking 33X12.5 procomp Xterrains. 4.56 gears and bushwacker pockets. hmm flames on the windsheild!! now how can I ...

why?? something I am missing here?