Search results

Possible New Lift Questions I am looking to buy some 4.56 or 4.88 ring and pinion gears and a mini spool for chevy 1/2 ton truck axles. 231-510-2754 or email direct jasonvess@yahoo.com

more on gears wanting to find a hartop and doors in good shape for a cj5 somewhere in the mid west, I am in michigan will travel to ohio, ill, ind and maybe further if price is right email me direct at jasonvess@yahoo.com

i am just going to weld them for now and when they break i will put some 3/4 ton axles under it thanks for all the advice

Well I have another toy a 76 fiberglass cj5 mud truck, currently running 38.5 super swampers on chevy frame with a 450hp drivetrain. This is only ran in the mud and at tough truck competitions so my questions are Will welding front and rear ends hold up? or should I weld the rear and get a...

anyone interested? I still have it?

let me take a better look at the t-case to see exactly what is broke

#4 sparkplug fouling I am looking at buying another jeep it is: 1990 wrangler sahara hard top, hard doors, 4.2 liter, 5 speed (i think but could be an Automatic) It already has a spring over conversion and a 2in body lift with 35" tsl swampers runs good and has a little rust the problem is...

ok motor has been sold again, I think

I will also consider trades, Email me direct with any ideas on a trade or PM Me with anything you have jasonvess@yahoo.com

hey gun nuts Was sold but buyer backed out due to travel time to pick up for sale a Reman 258 six cyl engine, was in a 1983 cj7, but is a direct replacement for 76-91 CJ's, Wranglers, and Cherokees. It has only 18,207 miles on it. It runs perfect, and has no known problems or oil leaks. It...

Hey, Snitty Well, I am not shipping it, I have $100 put down on it to hold it, a guy is coming to pick it up tuesday

The carb was sold and shipped out friday thanks for your interest

well after pulling the trans out, the throwout bearing still wouldn't work, so i called advance adapters to find out a 3 finger style diaphram on the pressure plate can not be used, it must be a raised diaphram style pressure plate. So after returning the clutch, and getting the correct one it...

ok, it's working, ended up being the feild wire was not getting 12v power when the key was turned on. thanks for all the help

Well Just got done putting in a chevy 350 into my jeep, the alternator will not charge it is a 10si or 12si, it is the same type of alternator, the 258 6cyl had. It tests good however will not charge. I have used the stock alternator wiring to hook it up, therefor one of the wires are...

Loud noise / sharp jerk when shifting Ok, I just got done putting in a 350 chevy into my jeep using a bellhousing adapter kit, chevy clutch, jeep trans, it is using the short gm throwout bearing that came with the clutch kit. Pushing the clutch in all the way to the floor will not completly...

i guess it would help there are for a small block chevy. Still interested i can take a couple of pics?

if the motor weighs 350lbs, fedex freight estimates shipping to be 320 to 450 depending which zip code and which class the engine would fall under. I am open to any other ideas? If you lived closer i would bring it for just the cost of gas

my grandfather used to be a truck driver and said he would delliver it to you for $400-$500 in northern alabama. he said it is a 1600 mile round trip, which would be $.25 per mile. He also said it would weigh less than 400lbs probally 300lbs or so. i am going to try and get some freight...

i shipped a dana 300 t-case to washington state from michigan for just under $100, it weighed 106lbs, but i have no idea how much the engine will weigh, maybe 400lbs? I may have someone that would be able to drive it down to you, i will check with him and get back to you.