Search results

1060094 is your steering stabilizer loose? is the steering box where it attaches loose? are your bearings in need of repacking?[addsig]

1060097 maybe you just need to run some injection cleaner thru the system. the injector tips might be clogged up and when you are under acceleration you have more pressure to force the fuel thru . not a bad idea to change the fuel filter ifn its been a while.[addsig]

1060102 how are your front wheel bearings any play does it go away depending which way you turn? how about your axle u joints. are they all rusty and hard to move or real easy to move ?[addsig]

1060105 check your front axle u joints.[addsig]

1060255 im not really good at describing how to do it. i just do it. you have to get the hub off and down to the brake backing plate. the seals at the end of the axle. pick up a chiltons and it will get more descriptive as to the how. its not that bad to do ,about the hardest part is getting...

1060256 why did it blow? thats the question you want an answer to. if it blows again i would suggest running an optional cell phone charger adapter . i have this problem a lot at the shop.[addsig]

1060259 if the fusible link is good check the power wire to the starter. if it grounds out you lose everything .[addsig]

1060265 in addition to greasing all the bushings see if the body mounts are ok. also check that the engine or exhaust isnt rubbing somewhere[addsig]

1060266 when i need something like a tester and snapon or mac is off the wall i try sears. most of the auto stuff has pretty good warantees too.[addsig]

1060269 i had a lighted switch for my back up lights and the bulb burned out i drove around the city blinding everyone behind me. whoops. the police pulled me over and set me straight. s..t happens lol[addsig]

1060275 i bought the speaker boxes that went around the roll bar at floor level w the cupholders. they are sideways and mostly not real visible but, if they want them they will get them.[addsig]

1060724 are you loosing coolant/level/ it sounds like you have a bad gasket and or head. when you get it all apart i suggest you take the time to get the head checked for any problems and if it has quite a bit of milelage on it,freshenig it up wouldnt be a bad idea either. if you have never...

1060728 it will bolt up to your transmission. it being an auto though , you need to get a standard flywheel and dont forget to put a new pilot bearing in. amc 258/304/360/401/4.2/4.0/ all share the same engine block bolt patterns. hope this helps[addsig]

1060730 whatever way you decide to go be careful about state inspection. the law states that if the vehicle had a cat then it must be there. by not having it you may end up failing the tailpipe emission tests. they test for 3 gases now . dont want to pop your bubble just some friendly advice. i...

1060732 cant we all just get along? lol seriously maybe someday you might purchase a newer jeep. i like to read and hear about all sorts of problems. maybe someone i know will need that kind of help someday. never stop learning and can never know everything. just wish we did lol.[addsig]

1060733 i purchased a used jeep that had a center console and it looked real nice but, when i tried to put it in my jeep it wouldnt fit because of the seat belts. see if you can call and get some measurements before you get it and find out it doesnt fit. most places wont pay you back for...

1060736 its gonna be like a new jeep only dont cost as much lol. good luck it all works out in the end.[addsig]

1060737 you probably want to do it yourself but most auto shops have a low pressure flush machine that works really well. its not real exspensive either. approx. cost 90.00 parts and labor with an additive to cut down on the acid buildup and lubricate water pump.[addsig]

1065866 sounds like misfire from wires cap or rotor, could it be transmission related also. drop into neutral , but keep motor somewhat on the go pedal and see if it goes away.[addsig]

1065723 hi everyone,been gone awhile. i had a problem recently and i pulled the drive shaft. i checked the u joints before i pulled it and it seemed fine. after i had it out i took the joints out and under one of my caps the needle bearings were dust. replaced the joints and even had the shaft...