Search results

I know you may have already heard this, but check and or change your tires. Had the death wobble in the worst way. I checked,tightened, reset, aligned, and blew sweet kisses at the thing. still wouldn't go away. Put new 30-10.50's on her and the wobble is gone completely. Good luck!

I am looking for a good used intake for my 91 cherokee and a good used headder for the same vehicle. Can anyone help? The ones at the junkyard are victums of the obama kill a car program and main engine parts can't be bought. Thanks for your help.

I know i'm no super jeeper like some of these fellas but my cherokee is at 300k and gets 23 to 25 mpg and runs great. I have an engine in the garage that I am building and will be dropping in this summer. The work is easy,except when I dropped the oilpan on my face and shoved my teeth through my...

I served in both U.S. Army and U.S. AirForce. Army; 1st.btn. 329 rgt. B company weapons, 101 airborne training, Michigan attached to ft. benning. Air Force; E.O.D. CHEMICAL WEAPONS SPECIALIST,Redstone arsonal, Huntsville,Alabama; E.O.D. Naval station Indianhead,Maryland; 380 bomd...

yes, i know this question has been asked a few times before. engine is a 4.0 i-6, i have replaced both hoses from the valve cover to 1) the airbox and 2)the intake port on the manifold. the only part i didn't replace was the grommet at the back end of the v.c. i'v read a dozen of the forum...

no. just going to bore it 30 over then rebuild. that will do just great.

is this an internal or external slave? very important.

that is what i was going to do in the first place, run the #1 up to tdc as i would for my cj. but what is the significance of the 15 pins between the timing dimples and will setting the timing gears as in the pic affect timing as this engine (when finished and installed) will be timed by the...

the timing marks i know. the positioning of them is the question. the chiltons says that for only the 90-91year modles the marks are to be set with the cam mark at the 12 oclock position and the crank mark at the 230 or so position (near three oclock per book) so that there is 15 pins between...

my 86 has the exact same problem. happened when the "tech" at the emission testing place wouldnt listen to me when i toldhim not to go over 1800 rpm . he promptly went to 2400 and dumped the rings on that cylinder into the pan. im doing a rebuild on her.

4.o 6 cyl

i'm rebuilding an engine for my 91 cherokee and i'm trying to give myself a migrain figuring the timing chain/gear enigma. according to the "book" the cam gear mark sets at the 12 o'clock position and the crank gear mark sets at just before the 3 o'clock position. if this were my cj it would be...

update to shipping. got the price down to 121 with smaller pallet. do you still want the tranny?

$200 plus shipping. should be $159 or less going ups ground.

shipping ups ground is 159.37 maybe a little less once it is actually weighed.

anyone out there have a resource for those 4.8 amp breakers for the wipers. thing plugs into the fusebox, just so we're on the same page. chrysler seems to think they are made of gold or something like it!:cry:

selling a bunch of wired switches. driver and passenger door controls, driver and passenger seat controls, ignition moduals, a cruise control modual, door handles, light sockets,.....$70.00 plus $16.90 flat rate shipping.

selling a 727 3-speed auto with lock up torque converter, np228 transfer case with vacuume shift motor, front and rear drive shafts. transmission has 70 miles on it, t-case has new seals, driveshafts have new u's and cv kit. $500.00 cash gets all. sold as a set.

my 1991 cherokee wiper motor/system won't turn off when turned on. i end up either unplugging the control modual or pulling the danged expensive breaker from the fuse box. the motor seems to be the culprit as the thing just dies. any of you fellas or ladies had this problem? what was your fix?

had the exact same thing on my 86 grand waggy. check the wires from the distributor backwards. i found many cracks on all those wires. when i put new wire in the bad wires place the problem went away. p.s. i love your german sheapard!